See what our Experts say about this Pro Series Trailer Jack

• Swivel Trailer Jack that Can Fit on 2-1/2 inch Diameter Pipe Mount
  The Pro Series jack part # PS1400300303 is designed to fit on a 2-1/2 inch diameter pipe and snap ring like you are needing so this would work great.
  view full answer...
• Can The Foot On The Pro Series Round, Snap-Ring Swivel Jack PS1400300303 Be Replaced With A Wheel?
  Hello Doug, thanks for reaching out. The foot plate on the Pro Series Round, Snap-Ring Swivel Jack # PS1400300303 is not removable. On some jacks it is possible to replace the foot, but with this Pro Series jack, the foot plate is part of the inner tube and isn't designed to come off. If you need a similar 2,000 lb jack with a wheel, take a look at the following: - etrailer Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 11" Lift - Zinc - 1.2K # MJ-1200B
  view full answer...
• Looking for a Bolt-On Jack That is Less Than 11 Inches When Attached
  The Pro Series Swivel Jack # PS1400300303 that you referenced should fit fine in your application. In the picture of the jack that I have provided has the measurements indicated. From the center of the mounting bracket to the foot plate is 11 inches. If you measure from the center of your frame to the ground you will see that you will actually have about 1-1/2 inches of clearance. I have also attached a short video with the measurements listed as well.
  view full answer...
  
• Trailer Jack Solution For Jack that Hits Tailgate When Down
  The # PSEA20000103 is one of the shortest A-frame jacks we offer from the mounting bracket to the top of the jack at 11 inches. The best solution I can recommend would be to go with a side mounted trailer jack like part # PS1400300303 that would install on the trailer frame behind where your current jack is so that you would have tailgate clearance when needed.
  view full answer...
• Availability of Trailer Swivel Jack with Pneumatic Tires
  If the tongue weight of your trailer is less than 500 lbs, the Trailer Valet Swivel Jack and Trailer Mover, part # STC-V211 might be a good choice. The jack swings up next to the trailer frame so it'll be out of the way of your truck tailgate and the jack features two pneumatic tires. This is the only jack we offer with pneumatic tires. If you click the provided link, you can see a demonstration video of the jack. The wheels on the jack are actually driven by one of the crank handles on...
  view full answer...
• Trailer Jack Compatibility with 14 Inch Tongue Space
  The Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs. by Dutton-Lainson # DL22800 has an overall length of 26-5/8 inches, so it will not fit where you are desiring. The height to the bracket when retracted is 13 inches, but the overall will to too long. The closest I found was the # PS1400300303 which is 11 inches to the center of the bracket when retracted as is # TJBB-2001-B.
  view full answer...
  
• Trailer Tongue Jack with Pneumatic Tires for Easier Operation
  Most A-frame campers like your 2019 Aliner Classic off-road model will have a caster wheel tongue jack that uses a hard plastic wheel. There are no replacement pneumatic tires that will fit in place of that wheel but there is a specialty jack product that does have dual pneumatic tires, the Trailer Valet 5X Swivel Jack and Trailer Mover # STC-V211. This unique bolt-on jack allows you to easily move and steer your camper thanks to its 2-speed hand crank operation. It even has an automatic...
  view full answer...
• How to Fully Open Tailgate on Truck and Not Hit the Trailer Tongue Jack
  The Roadmaster Dual Hitch Receiver, # RM-077-2, is designed to be used only when flat towing a vehicle. This product cannot be used when towing a trailer. Also, using any other hitch extension will cause you to loose 50 percent of your tongue weight capacity. If your truck hitch has a 300 lbs tongue weight rating, then using an extension will lower that rating to 150 lbs. The best option would be to go with a side mounted trailer jack, like the Pro Series Round Bolt-On Jack # PS1400300303....
  view full answer...
• Is Mounting Hardware Included with Pro Series 2K Swivel Trailer Jack
  Yes, the Pro Series trailer jack # PS1400300303 includes the mounting hardware. I have included a picture of it for you and a link to a video review of the jack.
  view full answer...
  
• Will the Pro Series Round Snap-Ring Swivel Jack Bolt on a 2 Inch Trailer Tongue
  The Pro Series Round Snap-Ring Jack, # PS1400300303, will bolt around your 2 inch trailer tongue. This jack can bolt to frames up to 3 inches wide by 4 inches tall and will have no problem fitting on your trailer. I have attached a photo showing the bolt hole dimensions of this jack for you to check out.
  view full answer...
  
• Would the Pro Series Round, Snap-Ring Swivel Jack Fit Round Tongue Trailer with Bracket Installed
  Sounds like you have a round tongue trailer that has a mounting bracket welded on it for a jack that match up with the mounting bracket of the part # PS1400300303 that you referenced. Normally we don't have a solution for round tube tongues aside from recommending they have a mounting bracket welded on. So since yours has one already that matches this jack this one should work well.
  view full answer...
  
• Recommended Topwind Trailer Jack for 2004 Viking Pop Up Camper
  For a replacement trailer jack on your 2004 Viking Pop Up Camper, I recommend looking at the Pro Series Round, Snap-Ring Swivel Jack # PS1400300303. This is a really nice topwind jack that will attach to trailer tongues up to 3 x 4 inches with the included bolt-on mounting bracket. This will give you 10 inches of lift and a lift capacity of 2,000 pounds. The bracket height when retracted is right at 11 inches. The jack features a spring-loaded, plunger-pin swivel feature that will allow...
  view full answer...
• Weight of a Whole Bunch of Different Trailer Parts
  I'd be happy to let you know the weights of all of the parts you asked about, and I'll even do it in descending order. - Timbren Axle-Less Trailer Suspension System w Electric Brake Hubs # A35RS545E: 134 lbs - Dexstar Steel Mini Mod Trailer Wheel # AM20545: 25 lbs - Pro Series Round, Snap-Ring Swivel Jack # PS1400300303: 13 lbs - Channel Tongue Trailer Coupler # CT-3002-Z: 4 lbs I have also attached links to video reviews of these parts for you to take a look at.
  view full answer...
• Picture of Pro Series Jack PS1400300303 Installed on a Trailer
  It looks like the Pro Series Jack part # PS1400300303 you referenced is installed correctly!
  view full answer...
  
• Installing a Swivel Jack on the Frame of a Cargo Trailer
  The etrailer Round Snap Ring Swivel Jack w/ Footplate # TJB-2001S-B is a swivel jack that is designed to be welded on to the frame of a trailer. If you are looking to use hardware to install a jack rather than welding the jack to the frame, I recommend the Pro Series Round Swivel Jack # PS1400300303. The Pro Series jack is a bolt-on swivel jack that includes the hardware needed to mount to your trailer frame. This jack will fit frames up to 3 x 4 inches. The jack is similar in cost and...
  view full answer...
• Will Pro Series Round, Snap-Ring Swivel Trailer Jack, # PS1400300303 Fit a 3 x 3 Trailer Frame
  I went out o the warehouse to verify the measurements on the Pro Series Round, Snap-Ring Swivel Trailer Jack, # PS1400300303. It will fit either a 3 inch by 3 inch tall or a 3 inch by 4 inch tall trailer frame. I have made a picture showing the measurements of the bolt holes for you.
  view full answer...
  
• Will Pro Series Snap-Ring Swivel Jack # PS1400300303 Fit on Mount for Older Fulton Snap-Ring Jack
  My contact at Fulton advised that their Magnum pull-pin snap-ring swivel jacks used a mounting ring diameter (2-1/2-inches) that is slightly different than what their sister-brand Pro Series uses on their Snap-Ring Swivel Jack # PS1400300303. This Pro Series jack may fit on the mount for your Fulton snap-ring jack but depending on its exact age it may not be an exact fit. My contact recommended you use the brand-specific mount for your jack. We also offer pipe-mount type swivel jacks that...
  view full answer...
• Diameter of Center Shaft that Holds Handle on Pro Series Round Topwind Jack PS1400300303
  I went out and to our warehouse and measured the center shaft on one of our Pro Series Round, Snap-Ring Swivel Jack Topwind # PS1400300303. The shaft is 1/2 inch in diameter. If you're looking for a replacement handle, the Replacement Handle for Top Wind Style Trailer Jacks # DL22674 will work well as it use the same size (1/4 inch) hardware and is right at about the same length (7 inches). Pro Series does not offer a direct replacement jack handle. If that's not what you're after, let...
  view full answer...
  
• Technical Specifications For Pro Series Round, Snap-Ring Swivel Jack PS1400300303
  Here are the technical specifications for the Pro Series Trailer Jack, part # PS1400300303. If you have any other questions about this jack let me know and I will be glad to help you out. I have also attached a photo of the jack and the mounting hole dimensions. Lift Capacity: 2,000 lbs. Dimensions: 17.5 inches L x 10.5 inches W x 5 inches H Weight: 12.2 lbs. Handle Style: Topwind Travel: 10 in....
  view full answer...
  
• Will the Pro Series Round Snap-Ring Swivel Jack Bolt on a 2 Inch by 2-1/2 Inch Trailer Tongue
  Yes, the Pro Series Round Snap-Ring Jack, # PS1400300303, will bolt around your 2 inch by 2-1/2 inch trailer tongue. This jack can bolt to frames up to 3 inches wide by 4 inches tall and will have no problem fitting on your trailer. I have attached a photo showing the bolt hole dimensions of this jack for you to check out.
  view full answer...
  
• Availability of Bolt-On Trailer Jack That Can Fit Round Tube Trailer Frame
  You are correct that all bolt-on trailer jacks require a square or rectangular frame member for installation. There is no bolt-on jack made for a round tube trailer frame since this would make securing the jack rather difficult; it would want to rotate around the frame tube whenever it was under load. You will need to have some steel material welded to your frame to allow jack installation. You can use a pipe-mount type like Swivel-Type # DL22685 which includes the weld-on pipe section.
  view full answer...
• Which Trailer Jack Do I Need for My 1994 Mastercraft Boat Trailer
  We do have some options for you, however we do not have anything that matches the bolt pattern of your current jack plate. Instead of trying to match the bolt pattern of the welded plate you can get a bolt-on jack that uses U-bolts to connect to the trailer. Which jack you need will depend on the weight capacity and height of your current jack. You'll also want to make sure the U-bolts will fit around the trailer frame. I've linked our selection of bolt-on jacks for you. A few examples...
  view full answer...
• Replacement Bolt-On Tongue Jack for Pole Tongue Trailer
  I recommend that you replace the entire jack and mount since there is no way to know for sure that the mounting base (that is welded to the trailer tongue) is still strong enough. Even if not actually damaged from the incident, it could be old enough to have metal fatigue that makes a new jack the best option, as you noted. Pro Series jack # PS1400300303 and the Bulldog # BD154107 that you referenced are both 200-lb-rated topwind jacks with a foot plate. Both offer 10-inches of lift, which...
  view full answer...
  
• Recommended Trailer Jack With Foot for Homemade Utility Trailer
  For a jack that is similar to the Round Swivel Marine Jack # MJ-1206B I recommend the Pro Series Round, Snap-Ring Swivel Jack # PS1400300303. This jack has a footplate instead of a wheel and has a 2,000 lb lift capacity. This features a bolt on installation and fits up to a up to 3" x 4" trailer tongue. The jack has an 11" retracted height, 21" extended height, and 10" of lift. The # PS1400300303 is also a swivel jack so you will be able to swing the jack up for travel and back down when...
  view full answer...

Do you have a question about this Trailer Jack?